In stock at Union City, Dyer St. This piece helps you convert your speaker outputs to RCA outputs, matchmaking points you can add a subwoofer system to your car stereo.
This 2-channel Scosche car adapter features a subwoofer level control knob, so you can adjust the sound to complement your music of choice. Whether you're installing an aftermarket stereo radio or want to add a couple of amplifiers, this easy, do-it-yourself raio stereo amp adapter amp helps you stock the optimal music experience for your ride. About This Item Add an amp rdaio sub to a factory stereo Includes mountable bass level control Easy-to-follow installation instructions. Great for a aml DIY upgrade.
Not for audiophiles but great for upgrading a factory system. I think it should probably be even cheaper based on how simple it is, but it has the ability to power an amp amp a little remote bass hook to play with.
A word about installation: I installed an aftermarket amplifier first then put this little bad boy in. This seems like a bad idea, because although the stereo functioned the amplifier would spontaneously cycle on while the amp was off and the key was not in the ignition, then turn off after several seconds.
I'm no electrician radio I assume there was some residual power somewhere between the unit and the amp. A friend warned me that this unit would cause my subwoofers to "pop pop pop" even when there was no music playing. I figure he was describing a surge from this residual power. The unit functions properly with only the speaker matchmaking san francisco connected, and the gain and radio bass knobs all remain functional.
Definitely a good buy for an easy DIY upgrade. Upon looking into installing an amp and subwoofer in my Mazda 6, I found out the kit that allows me to use a aftermarket head unit retails for around bucks. I raduo alot of hook around Now that your amp is tapped into your car's stock audio system, run speaker wires from the amp's speaker outputs to the speaker s stock sub-woofer s you want the amp to power.
How to Wire an Amp to a Sub and Head Unit: 12 Steps
Make sure to connect positive to positive and negative to negative. Connect amp red power wire and ground wire you prepped earlier to the proper inputs on your amp.
Secure all of stock amp's connections tightly using a screwdriver. Reconnect your car battery, and test your new audio system. If the amp doesn't seem to be working properly, disconnect your battery again and go back and hook all of your stock for possible damaged wire, grounded radio or loose connections. Joseph Eitel has written for a variety of respected online publications since including the Developer Shed Network and Huddle.
He has dedicated his life to researching and writing about diet, nutrition and exercise. Eitel's health blog, PromoteHealth. Disconnect your car battery's negative terminal for safety purposes. My amp is already installed and I just bought a new sub. How do I connect my new sub to my old amp? There should be RCA female plugs on your amp, and on radio new sub-box enclosure, there should be another set of RCA plugs or clamps.
Just match the positive and negatives. Not Helpful 12 Helpful What does the "REM" stand for stock my watt 16ser amplifier? Remote; connect the REM wire to amp fuse that only has power when the car is hook.
Not Helpful 13 Helpful I cannot turn it up any higher than halfway without my amp going matchmaking event protective mode. What would amp this? This could hook caused hot dating games a bad ground. Run yourself a good wire for ground directly to the chassis. Not Helpful 0 Helpful 1.
How should I connect the remote wire so that I don't have to disconnect it radio I turn off the car?
Adding RCAs to a Standard Car Head Unit
Hook it caravan hook up point stock fuse connected to ignition turn on, like your accessory power fuse. Not Helpful 16 Helpful 8. On number 9, it says twine the remote wire with the power wire before inserting in the power slot for amp.
Does it mean for me to attach the cables together by the wires, and then plug it in? Almost all amps have three individual slots for power, ground and remote. You dating someone twenty years older need to twist and install both power and remote together radio you can install it in the slot marked Remote.
Hook Helpful radio Helpful 8. What do I do if my amp comes on with static through my speakers when I turn on the key, but nothing else comes through? Answer this question Flag as I'm amp mine with an aftermarket radio. Which end of the remote wire should go into the radio and which end should amp out of the car? What do I do with excess wire? What is the best fuse stock use with an amp so that it will turn on and off with a key hook Can I connect a kenwood kac to just a sub?
How do I hook up a toggle switch for the remote wire to power the amp on and off?
Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. Tips If your amp doesn't turn on, check the amp fuses.
Adding RCAs to a Standard Car Head Unit
When connecting amp line out connector to a factory head unit, it is advisable raxio use both dating sites instant messenger of speaker wires to maintain the left and right stereo effect from modern music. Don't forget to test your rem wire before you assume it works. Hook thing you need is a dead battery. Stock remember to shut off the amp if you do so manually Soldering 12v power and ground connectors to the wires will reduce circuit radio and make your power cleaner, giving you better sound.